Downspout Drainage to Sewer Clogged or Leaking Pt3

Ok I admit it. I‘m a slow bastard. This series of photos has been sitting on the camera really for MONTHS and I’m only finally putting them here, in Part 3, today. You know what happened don’t you? The finish to this project came at a busy time, and it was so easy to do I just got to thinking “hey they can probably figure it out on their own…” and blah, blah, blah, I was too lazy to get back over here and upload the pictures and write a few words to go with it. And the WORST part is I still need to do a Part 4 to show what happened to the downspout on the other side of the house because it was a totally different situation. But I PROMISE I’ll do that with the week! All-righty, so where’d we leave off? Right, there was this hole in the ground and a downspout hanging, and I needed some kind of pipe or something to connect to the sewer line.

dsc03350.JPG

So the original plan was to go get regular tile/ceramic pipe section as seen in Part 2 of this series to replace the broken one. But here’s the problem; the connecting lip on the pipe wasn’t going to fit. I mean the reason it was broken in the first place was because the underground pipe section was too close to the house, so they had chipped 20 percent of the lip off so that other 80 percent could fit. You may not have this problem so you can probably go to the store and buy a regular replacement pipe. I decided to go another way. I went to Home Depot and I saw 2 things in the gutter department that I could jimmy together to server MY MASTER PLAN! The first thing was a flexible gutter-to-downspout section. And the next thing was a metal connector unit. It occurred to me that I could use this setup to connect the downspout to the sewer pipe underground and the flexibility could allow me to get the 2 parts joined perfectly.

dsc03354.JPG

And the pipe underground was almost exactly the right size, but the flexible joiner had this squared off section that did NOT fit inside the hole. I decided to cut it off. And the photo below is NOT how I did it, but I wanted to indicate “cutting” with a photo, so I took this picture. I did think about doing this but, that was wrong kind of blade anyway.

dsc03355.JPG

But here’s how easy it was to install. Just stick it in the hole onto the next pipe. As you can see in just one day we had some winter winds blow a bunch of leaves in my cold hole.

dsc03357.JPG

I took some waterproof adhesive and applied it to the sewer line pipe in the ground, and you can see that stone that would have gotten in the way of a pipe with a lip too next to the wall (on the left side of the pipe).

dsc03358.JPG

Here’s all the pieces connected. I and I know it looks crooked, but I haven’t even put the dirt in there yet. Remember the goal is to get flow from the downspout to the sewer. At the beginning of this project that was NOT happening. The pipes were full of mud and debris and the pipes were so ill-fitting that whatever water did manage to go down the pipes would just seeping into the ground. Once I connect the downspout to the house with one of those metal straps it’ll be straight again.

dsc03359.JPG

It had gotten so cold here in Chicago that my wet dirt had FROZEN. And to get it loose I actually had to get a pick to break it up into clumps. And then stick, basically, a bunch of rock shaped dirt back into the hole. I knew that once it warmed up it and got wet it would settle and fill up all the air pockets. And that’s exactly what happened; it got hot for few days, rained, the dirt sunk, and then I had to find some more dirt to fill up the depression.

dsc03360.JPG

Ok so here are all the pipes and dirt put back together just like Humpty-Dumpty. And there’s some of my frozen dirt that had to melt before I could put it back in the hole. Oh and one last thing-the flexible replacement “pipe” was only about 7 dollars so it was not only a practical solution to the problem but cheap! And by the way…Need a local handy person? Check Service Magic Call them at 877-576-3375

dsc03361.JPG